WARNING! ... ... The first step of reflashing a 32bit ECU is to erase the stock map/software image. There is no provision for backing up the stock image or unerasing it. Make sure you flash the correct file and know what you are doing before using t...
Building a programming device to reflash the 2002-2007 busa ECU is extremely simple. The most complex component a TTL to RS232 converter can be bought ...
... The listed ECU files are map files only and do not include the software sections. They are 96k files and the map data is located between 0x0001:0000 and 0x0001:7FFF. 0x0000:0000 to 0x0000:FFFF i...
I am going to put these on my install CDs, but hopefully this gives the new person to flashing an easier time setting up the hardware, software, and flashing process, any thoughts? ... .....
If you have FDT installed and set up properly like explaned in here: ... http://www.activeboard.com/forum.spark?forumID=99460&p=3&topicID=14963290 ... ... ...and if you have an interface hardware ready and installed on your bike like explain...
... ... The Enginuity/RomRaider definition file disscussed in this thread can be found here. ... ... The 32bit busa limits are very much like the 16bit limits. They share all the same values. The major difference is that the Fuel and Ignition limi...
Having built or sourced an hardware interface, the next challenge is how program the ecu flash having done some changes to the firmware. ... ... The software to do that is downloadable from the ecu processor manufacturer called renesas from the foll...
I've posted an updated Enginuity definition for 99-01 16 bit Busas (-24F20, -24F21, -24FD0) with improved RPM limiting capability. ... ... See 16bit Map Thread ... ... I had someone request a specific configuration so I went back to recheck earlie...
This may have been addressed but i search and couldn't find it. I had this to happen on 2 bikes that I flashed the ecu's on. Both were first gen busa's, built motors with aftermarket injectors and fuel system. When pulling the bikes on my dyno, when ...
Sorry for the dumb qustion. ... ... Is ti possible to copy and paste a fuel table , that was modified in another program into an ecu editer fuel table ? ... ... Thanks ... ZX10Bud...
Alright everyone,i have started a new thread on this subject for the reasoning of all of us being on the same page.I had talked to rr today in depth on how this should be implemented correctly. We had talked and come to the agreence that we should le...
I have all the other items needed laying around but the pins are been a pain to locate, and paying $48 to have them shipped from motec is stupid IMO. My bike is currently in storage 20 ...
Looking to buy the ecu editor that boostbysmith sells, ... ... i am not a tuner , i am looking to change rev limiter , remove the top speed restriction and adjust the timeing ! ... ... does anyone know or have any settings for the timeing on the ...
While reading the code (for yoshbox and stuff) come to read the ambient pressure sensor stuff... ... ... Basically ambient pressure is used for two things: ... - While on vacuum (IAP maps) the ambient - manifold pressure sets the X-axis for map valu...
... Hi , This message is for PetriK... ... ... Is it possible to dump the entire memory of the ECU via the serial interface TX and Rx (max232) with FTD 4.01? ... ... If not ... ... What is the way?? ... ... Thanks in advance... ... ... BR ... ...
Can anyone tell me if there is a nuetral fule map in the ROM raider defs? I want to fattrn up the fuel for my launch control to spool up the turbo. but I am not aware of a nuetral fuel map for when the clutch switch is activated. ... ... Does this e...
... Hello everyone, I've been following you guys for a long time now and decided I'd try to get into reflashing. I have an '03 1000 that I've built and I need more tuning capability. ... ... ... ... My question is... How high can the 32920- 24FK...
... I've been reading these boards for quite a while and I am starting to get the idea of hacking these ECU's. From my previous ECU expeiances the ECU holds a checksum value in the data. Everything I've checked on these forums I have yet to find a...
Can anyone confirm that logging for the purpose of tuning is possible using the Innovate Plugin, found HERE, together with the following: ... ... - Innovate XD-16 Standalone Gauge...
can someone help bike wnt start it flashes up -c42 imobiliser fault the bike shop wants my kidneys to fix bike is a gsxr 1000 k6 is it possible to bypass imobiliser...
Please excuse me if this has been covered before, and I'm pretty sure I've already answered my own question, but want to as here before I go changing anything and losing my tune/previous settings. ... ... I had my bike tuned, setup for a shifter and...
hmmm anybody know what kind of k line adapter would be needed for a other ecu to communicate with the dash? Id like to use a motec to drive the factory dash? ... thanks, ... Seb...
Has anyone flashed an ecu to death yet? I believe they were only spec'd for 100 flashes. I imagine they will last for many more than that, but just curious if anyone has killed one? ... ... John...
from what petrik has said on the gen2 side is that there will be a code shareing/distrbution for the gen1 owners/users. does anyone know about this??? maybe jasa will be headding this up..???? This is great news and will give me a re-newed intres...
